PLUMBING 101: TIPS FOR BATHTUB INSTALLATION

Plumbing 101: Tips for Bathtub Installation

Plumbing 101: Tips for Bathtub Installation

Blog Article

Visit The Following Page

We've stumbled upon this post about A Step-by-Step Guide to Installing a Bathtub listed below on the net and thought it made perfect sense to relate it with you in this article.


Installing A Bathtub
Installing a bath tub isn't exactly rocket science, yet it does need solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a moderately tough project. If the old tub is conveniently available, the task can move immediately; if you need to open a wall surface to get rid of the old tub and also place the brand-new bathtub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. See to it you have certified yourself for the task and also are comfortable trying it. Instead of working with a service provider to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you start. Chances are you may require an expert plumber to make tube connections.
This article will certainly help you mount a new tub in your restroom if you have currently acquired a brand-new tub as well as do not need to change the arrangement of your previous supply of water pipes.
Your tools and product checklist need to consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Removing Old Taps


    If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you need to do is detach the water system. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing faucets can be quite troublesome due to the limited gain access to that is typically the instance.
    Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will originate from the pipelines. Once the supply pipelines have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
    Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the new faucets are plastic, then you will need a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a connection to the current supply pipes.
    If you need to fit a monobloc, then you will certainly need lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in area in between the tap and also the sink. Protect the faucet in place with the producer provided backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be attached to the tap finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.

    Mounting the Bath tub


    Utilizing the two wood boards under its feet, put the bath tub in the called for setting. The wooden boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
    The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the spirit level and changing the feet on the tub until the level reads degree.
    To set up faucets, fit the bottom of the outermost flexible tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other faucet.
    Activate the water system and also examine all joints as well as new pipework for leakages and also tighten them if required. Fill the tub and likewise examine the overflow outlet and also the regular outlet for leaks.
    Lastly, fix the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub ought to wait up until the tub has been utilized at the very least when as this will settle it right into its last placement.

    Getting ready for the Installation


    Firstly, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the manufacturer's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets unit to avoid stress on the bath tub.
    Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use all of the provided washers.
    Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to now be ready to be fitted in its final position.

    Tiling Around the Tub


    In the location where the bathroom satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack an inflexible seal, causing the water to permeate the wall surface in between the bathroom as well as the tiling, bring about complications with dampness and possible leakages to the ceiling below.
    You can select from a range of coloured sealants to blend in your fixtures and fittings. They are offered in tubes and also cartridges, and can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill up the tub with water prior to sealing, to enable the activity experienced when the tub is in use. The sealer can break fairly very early if you do not take into consideration this motion prior to securing.
    Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    As an enthusiastic person who reads about A Step-by-Step Guide to Installing a Bathtub, I figured sharing that excerpt was appropriate. Sharing is nice. You never know, you may just be doing someone a favor. Bless you for your time. Visit again soon.


    Get Offer

    Report this page